Anchor
_Understanding_the_Various _Understanding_the_Various

Anchor
_Toc151867352 _Toc151867352

Anchor
_Toc200860528 _Toc200860528

Anchor
_Toc237141076 _Toc237141076

Anchor
_Toc487792005 _Toc487792005

Understanding the Various Meter Types

RTA tracks several types of vehicle meters. It's important to understand how they work because vehicle cost per mile and miles per gallon reports use the various meters. The meter types are as follows:

• Primary Meter: This is the current vehicle meter reading, sometimes referred to as the work meter. It is the most up-to-date meter reading and is updated throughout the RTA system.
• Fuel Meter: This is the most up-to-date meter reading entered through the options in the Fuel Inventory module. This is tracked separately from the primary meter to ensure MPG figures are properly reported.
• Alternate Meter: This is the meter reading for other types meters that might be on the vehicle (e.g., hours, yards, cases). This meter has no ties to the Primary or Fuel meters. Refer to "Alternate Meters" for more information.
• Life Miles: This is the accumulated miles traveled for the life of the vehicle. The life miles can have the same or higher reading than the Primary and Fuel meters, but never a lower reading. Life miles continue to increase even though Primary meters may rollover or get reset to 0 when replaced.
• Base Miles: This is the number of Life miles the vehicle traveled prior to being tracked in the RTA system. This number doesn't change when meters are updated and/or adjusted. It's subtracted from the Life miles to ensure vehicle lifetime costs are properly reported. For example, suppose a vehicle had 50,000 miles on it before you started tracking it in RTA. After the first month, the vehicle travels 1,000 miles and incurs $250 in fuel and maintenance costs.

!worddavf143ca96352029b1735921a7913168c7.png|height=42,width=365!

...

Lifetime cost reports for this vehicle, with no Base miles, inaccurately reflect this vehicle as costing $ 0.0049 per mile (250 lifetime costs in RTA ÷ 51,000 miles).
Lifetime cost reports for this vehicle, with 50,000 Base miles, properly report this vehicle as costing $ 0.25 per mile (250 lifetime costs in RTA ÷ \ [51,000 miles - – 50,000 base miles\]).
The Primary meter is updated throughout the entire RTA systemin the Work Order module while creating or posting to existing work orders, in the Tire Inventory module while mounting or dismounting tires, in the Vehicle Inventory module while entering PM information or creating vehicle warranties, in the Fuel Inventory and EFI modules, and through TriCoder uploads. Basically, anywhere the system prompts for an odometer reading, it is prompting for the Primary meter reading.  
Fuel entries are the exception, however. Fuel transactions can be entered using the *Many* *States* the Many States (FFM), * Quick Fuel Entry*  (FFQ), * TriCoder Input*  (FFT), and *and Electronic Fueling*  (FFE) options. Meter readings entered through fueling options update the Fuel meter, and if the meter reading exceeds the current Primary meter reading, the Primary meter reading will be updated as well. Therefore, a Fuel meter will always have the same or lower reading than the Primary meter, never higher.  
When the Primary meter has a higher reading than the Fuel meter, the difference is referred to as "Add miles." Pay close attention to Add miles at the end of an accounting period. Depending on how the "[Tracing Fuel Cons<ac:structured-macro ac:name="anchor" ac:schema-version="1" ac:macro-id="98070508-36d1-42b1-9687-b664d15220c7"><ac:parameter ac:name="">_Hlt40574979</ac:parameter></ac:structured-macro><ac:structured-macro ac:name="anchor" ac:schema-version="1" ac:macro-id="6c383bdf-3889-4705-8a95-609853cc1afa"><ac:parameter ac:name="">_Hlt40574980</ac:parameter></ac:structured-macro>umption|RTA System Parameters#switch_tracing_fuel]" switch is set (SSM, Fuel Parameters tab , switch 1), existing Add miles will either be zeroed out and accounted for in the current period OR be carried over and accounted for in the new accounting period. If you're tracking fuel usage in RTA, we recommend setting the "Tracing Fuel Consumption" switch to _YES{_}. When a meter reading is entered in " switch is set (SSM, Fuel Parameters tab , switch 1), existing Add miles will either be zeroed out and accounted for in the current period OR be carried over and accounted for in the new accounting period. If you're tracking fuel usage in RTA, we recommend setting the "Tracing Fuel Consumption" switch to YES.
When a meter reading is entered in RTA:

• The current meter reading is updated only when a higher reading is entered—as long as the mileage difference does not surpass the limitations defined in the class codes, EFI process settings, or system parameters (MVC, FFEM, or SSF, switch 27).
• The current Life miles are updated only when a higher reading is entered, again, as long as the mileage difference does not surpass the limitations defined.
• Entering a lower meter reading does not update the current odometer (unless you're in one of the change odometer routines). This allows you to enter old, misplaced, or out of order transactions without affecting the current meter readings.

...

The second transaction, Fuel entry 1, shows a meter reading of 100 was entered through a fuel transaction. The Primary meter and Life miles remain at their current settings since the value entered is lower. The Add miles is reduced by 100.
The third transaction, Fuel entry 2, shows a meter reading of 500 was entered through a fuel transaction also. Both the Primary and Fuel meters are updated since the new reading is higher than the current readings.
The fourth transaction is similar to the first one. The last transaction doesn't affect any of the meters because the meter reading entered is lower than the current readings.
RTA tracks the Primary and Fuel meters separately in order to correctly compute miles per gallons. Doing so prevents miles per gallons from being overstated when a work order is done at a higher reading, but fuel entries haven't yet "caught up" to the meter reading on the work order. Take a look at transaction 4, for example, even though the actual vehicle meter reading is 750, miles per gallon reports will use 500 in its computations because that will "match" the number of gallons from fuel entries; using 750 would make the vehicle appear as if it's getting better mileage than it actually is.

Anchor
update_meters update_meters

Anchor
_Toc151867353 _Toc151867353

Anchor
_Toc200860529 _Toc200860529

Anchor
_Toc237141077 _Toc237141077

Anchor
_Toc487792006 _Toc487792006

Updating Meter Readings

Because meters are automatically updated as transactions are processed in RTA, it may not be necessary to manually update vehicle meter readings. As long as the data entry is current and up-to-date, your vehicle meters will be too. However, if you're not tracking fuel usage you'll need to update meter readings manually or via a hand-held TriCoder since your vehicles will only come in occasionally for maintenance services (and you won't know when to bring them in if the meter readings aren't updated). Some fleets like to update meter readings at the end or beginning of an accounting period even if fuel usage is tracked. This section explains the options available for updating the meters.

Update Work Odometer

This option updates only the Primary meter. If you're tracking fuel usage, use Quick Fuel Entry (FFQ) for updating meters instead because this option does not update Fuel meters. To update Primary meters using this option, follow the steps listed.

...

You can quit at any time by choosing Exit. If a vehicle record is in use, you'll be given the option of skipping the odometer update for that vehicle or waiting until the vehicle record becomes unlocked.

Quick Fuel Entry

This option updates the Fuel meter, and also the Primary meter if the meter reading entered is higher than the current Primary meter reading. To use this option, do the following:

1. Select Fuel > Fuel Entry > Quick Fuel Entry from the RTA main menu (FFQ).
2. Enter the facility number or press F1 to select a facility from the lookup list.
3. Choose Yes if the prompt to enter miles/kilometers/hours only is displayed. This prompt may or may not appear, depending on how the "Enter Miles Only" switch is set (SSM, Fuel Parameters tab , switch 7); you'll be able to update the meter regardless of the setting.
4. Enter the facility number and/or the vehicle number to update or press F1 to make the selection from a lookup list.
5. Enter the date or press F1 to select a date from the calendar. This could be the date the reading was taken or the input date.
6. Enter the new meter reading when prompted. The items you're prompted to enter depend on the settings of several switches in the Fueling Parameters (SSM, Fuel Parameters tab ). Enter or skip the entries as needed. Refer to "Fueling Parameters" and "Quick Fuel Entry" for more information if necessary.
7. Choose Post to complete the entry.

Odometer Update TriCoder Program

A hand-held TriCoder program designed specifically to update meter readings is available. It provides a fast and easy way of updating numerous vehicles at once—prompting simply for vehicle number and odometer reading. When the collected data is uploaded to the RTA system, the primary vehicle meter will be updated. For instructions on using this program, refer to "Odometer Update" in the TriCoder Programs section of Chapter 8—Bar Coding.

Updating the Meter Using the Change Odometer Program

1. Select Vehicle > Change Odometer from the RTA main menu (VH).
2. Read the message displayed and choose Yes to continue.
3. Enter a vehicle number or press F1 to select a vehicle from the lookup list.
4. Choose Broken Meter, Correction, or Roll Over to indicate the reason for the odometer change.
5. Review the vehicle information displayed. Go to "Change Odometer Vehicle Information."

Updating the Meter Through the Vehicle Record

1. Select Master > Vehicle > File Maintenance from the RTA main menu (MVM).
2. Enter a vehicle number or press F1 to select a vehicle from the lookup list.
3. Select Utilities > Change Odometer from the menu or click on the Change Odometer icon in the toolbar.
4. Read the message displayed and choose Odometer to continue.
5. Choose Broken Meter, Correction, or Roll Over to indicate the reason for the odometer change.
6. Review the vehicle information displayed. Go to "Change Odometer Vehicle Information."

...

• Year, Make, and Model: This is the vehicle's year, make, and modelreview model-review it to make sure you are about to change the meter for the correct vehicle.
• Meters: Current, Fuel, Period, and Life: This displays the vehicle's current Primary meter reading, the current Fuel meter reading, the current period miles (miles traveled this period), and the Life miles.
• Known miles (included in period & life) not posted: This displays the Add milesthe miles-the difference between the Primary and Fuel meters.
• Last recorded meter reading: This displays the current Primary meter reading.

Examples for Changing Vehicle Odometers

Example 1: Replacing a Broken Meter
In this example, we will replace a meter that broke at 50,000 miles. While the meter was broken, the vehicle traveled 250 miles. A new meter was later installed.
Choose Broken Meter as the change odometer reason and the odometer change utility window is displayed.

...

After this correction has been made, the vehicle's current and fuel meters will be 500; the period meter will be 3,500; the life meter will be 100,500.

Anchor
_Toc151867355 _Toc151867355

Anchor
_Toc200860531 _Toc200860531

Anchor
_Toc237141079 _Toc237141079

Anchor
_Toc487792008 _Toc487792008

Changing a Meter Type

To change the Primary meter from one type to another, do the following:

...